How To Put Jack Back In Silverado
Almost all Chevrolet Silverado models are equipped with a jack kit as standard equipment. It is often purposely disassembled to avoid rattling noises.
This is due to the fact that the jack establishes a crucial position in the jack assembly, which allows you to drive without rattles.
If you have ever tried to disassemble the jack kit on your own, you will understand how difficult it is to reassemble it.
Learn how to put jack back in Silverado in this post if you don’t want the noise to bother you as you continue reading.
Steps To Put Back Jack In Silverado
The procedure is divided into several steps: The first is to identify the place where the Jack will be placed, then determine the proper position of the Jack and, finally, place it.
Step 1: Locate Jack kit
The location of your jack depends on the type of car you have; on a Chevy Silverado, the jack is often located under the passenger seat on the driver’s side of the vehicle.
The base of the jack is held in place by a bracket that is inserted into a hole in the floor and sits on a plate.
It is easy to notice by the bright yellow color of the knob or handle, which will be pointing outward if the jack is exposed to the elements.
Using this handle, you can remove the jack kit from its current position.
Step 2: Remove jack kit
To remove the jack kit, turn the knob/handle clockwise. Turning the knob clockwise should be sufficient to loosen the screw.
This will progressively extend the jack kit and allow the other end to gradually release as well.
If you are replacing a jack kit, you will need to remove it from the recessed angle first in order to replace it properly.
Remove the nut from the back of the recessed piece and replace it with a new jack kit, inserting it into the recessed angle in the same manner as you did with the old one.
Step 3: Jack Kit Reinstallation
After successfully removing the jack cylinder on your Silverado, it is time to reinstall the jack.
To replace the jack, start by aligning your new jack kit with the recessed angle and tighten it securely so it will not move during operation.
Then, with the jack and recessed angle in place, you can adjust the wheel hook or chalk to your liking.
Turn the yellow knob one more time, but this time in the opposite direction of the last rotation.
Turn the knob until it is securely connected to the chalk and does not rattle when not rotated.
Check to see if the jack kit rattles or shakes by shaking it. If it does not, the process is complete.
Where is the jack on Chevy Silverado?
On the driver’s side, towards the rear of the vehicle, on the floor, there is a metal box sunk into the panel.
Make a U-turn to expose the tire irons by unscrewing them. The jack can be found on the passenger side or on the left side of the rear cab of the vehicle.
What size jack do I need for a Chevy Silverado?
For the Chevrolet Silverado 1500, a 2-ton floor jack is highly recommended.
Are 3 ton jack stands enough for truck?
The three-ton jack stands are capable of supporting a maximum weight of 6,000 pounds.
This leaves you with an additional 2,000 pounds of load capacity for the pair of jack stands.
A pair of 3-ton jack stands will be sufficient to lift and support almost any car on the road.
Will a 2 ton jack lift a Silverado 1500?
The jack is rated for a safe working load of 2 tons, which is the maximum load it can safely support.
However, since a 4-wheel vehicle is usually elevated above the ground, a small jack that is fully extended will not be particularly stable in that position.
How much does it cost to jack up a truck?
Lift kits in the smaller scale category can raise a vehicle two to five inches and are typically priced between $400 and $12,000, depending on the manufacturer.
Lift kits in the larger scale category can raise a vehicle six inches or more and are typically priced between $10,000 and $15,000 total.
Standard leveling kits are typically priced between $200 and $1,000.
Final Thoughts – How To Put Jack Back In Silverado
And so much for our writings on how to put the jack back in Silverado. Essentially, it’s the same as changing a flat tire or adjusting your SUV’s suspension.
Our specialists have covered everything there is to know about jack kits to ensure you and your loved ones have the best driving experience possible.